Ezigrade (version 2)
GPS Pickup
 
Most Grading systems (for example Field Level2, Farmscan etc) will pick up the data for you directly; and if available we suggest that you use there supplied option.
 
If you do need to pick up your data directly then. Firstly the GPS needs to support NMEA GGA codes and it must be set running to put out this data. Most commercial GPS units we know of support this data output. Also be aware that the GPS needs to be an RTK for the height value to be accurate enough for land grading.
 
If you are running Ezigrade on a John Deere system then we suggest you also look at the "Running Ezigrade under Igrade" section of this manual.
 
GPS Options.
 
From the "File" menu select GPS and then "Options". This sets the various pickup options available in Ezigrade.
 
The first entry is the Antenna Height and you would need to set this at least once. The default value is preset to zero. The data can be picked up at a predetermined time interval, at a predetermined positional change or only when you wish by clicking on the add option. Normally for broad acre data pickup we would pick up the data via Position Change. Enter the value in meters or feet to set this value.
 
Some systems may also have this option withing the GPS controller. If so the value only needs to be set in one place.
 
Ezigrade picks up data in UTM (Universal Transverse Mercator) coordinates.
 
 
 
We suggest that you normally work in this mode. However Ezigrade also allows you to work in local coordinates. In this mode you would select a point and set this to be the zero, zero point. All points are subsequently added in referenced to this point. Ezigrade stores the coordinates of the local reference point in the registry if you need to pickup further points at a later date. However if you do a new job and change the local coordinates then the original setup coordinates will be lost from the system. We suggest that you write them down somewhere.
 
Num Sats.
 
This is shorthand for the number of satellites. For data consistensy we often wish to flag a warning or an alarm if the number of satellites visible drops below a preset number. On the GPS bar we would display green if we have sufficient satellites. If this number drops it changes to Orange and if it drops below the warning level then displays Red. An audible alarm is sounded. There is a further option to disable data input at this time if this is what you require.
 
HDOP variation.
 
HDOP stands for Horizontal Dilution of Position. It is a good indicator of the precision of the GPS reading received. To estimate the accuracy multiply this number by the quoted GPS accuracy. For example if your GPS is good for an accuracy of 5 meters in stand alone mode but the HDOP value is 4 then the data is only accurate to 5*4 ie 20 meters. Enter your values here for the values you will set a warning and an alarm as necessary.
 
Show Precision.
 
Rather than display the HDOP and VDOP values Ezifield can estimate a precision value for you. Set the GPS accuracy values for RTK,DGPS and GPS mode. Ezifield knows which mode the GPS is running in and can display the expected precision value.
The remaining tick box's allows you to set alarm's and stop GPS pickup automatically if your data falls outside the appropriate ranges.
 
GPS Serial Port
 
 
From the "File" menu select "GPS" and then "GPS Serial Port". Make sure that all radio buttons are selected and the connector field is set to the appropriate serial port. If you are using a Bluetooth GPS or a CF/PCMCIA GPS then you may need to refer to it's driver to ascertain the serial values to match that of the GPS.
These values would normally only be set once. The values are retained in the registry and are available the next time the software is run.
 
 
 
 
GPS Pickup
 
From the "File" menu select "GPS" and then "GPS Pickup". Ezigrade now starts checking the serial port for a NMEA GGA string. Two additional toolbars are displayed with_in Ezigrade. The first Toolbar shows the values contained within the GGA string. Ie The latitude and longitude. The antenna height shown is the preset value. The last box contains some debugging messages that will be refined in time.
 
The second ToolBar shows the calculated Eastings, Northings and Height together with the number of satellites and a field for HDOP (Horizontal Dilution of Position), VDOP as well as the mode the GPS is running in. ie normal GPS, Differential GPS and RTK GPS. The two ToolBars are shown below:
 
 
 
 
 
There are a number of bitmap icon's which relate to GPS activity's. The serial port icon brings up the baud rate etc options. The traffic light icon is an on/off switch. If GPS pickup is running; pressing this button stops pickup. If GPS pickup if stopped pressing the on/off icon turns it back on.
 
The “+” icon will enter a point at the current GPS position.
 
The red/green triangle icon shows the difference in height between the current GPS position and the active triangle surface. This can be a design surface and will give you the height difference from current to design.
 
The compass to point icon is for a point setout and shows bearing and difference from the present GPS position to the point specified.
 
 

Made with help of DrExplain

TODO: Change the footer's content in Project Settings : HTML (CHM) Export : Setup HTML Template and Layout